Hand injuries will continue if we rely on gloves alone. How could they stop, when workers’ hands are still being used to guide, position and control materials in hazardous areas?
Gloves are important, but they protect the hand while it is doing the task. They don’t remove the hand from the exposure.
A multinational company is in an unusual position to change that. Its standards, engineering requirements, purchasing decisions and contractor expectations shape how work is done at every site it runs. This article is about using that reach.
Injury rates show where hands were hurt. They don’t show where hands are still exposed.
Companies count injuries. They rarely count exposure.
Most global safety dashboards are built around outcomes: lost-time injuries, recordable cases, severity rates. These numbers matter. But for hand safety they arrive late. A site can report a clean month while the same hands go back to the same suspended loads, pinch points and closing gaps every shift.
That leaves a gap between what leadership sees and what is happening on the floor. The exposure is present every day; the indicator moves only when someone is hurt. By then, the only question left is what went wrong.
PSC’s view is simple: before asking which glove to wear, ask three questions.
Where does the hand enter the task or hazard?
What function is the hand performing?
Can that function be performed another way, keeping the hand farther from the hazard?
This is the thinking behind Find The Hand™: find the exposure, understand why the hand is there, then explore how to engineer it out of the hazard. For a multinational, the next question is how to make that thinking part of the way every site is managed.
Different plants, different countries — the same hand functions
Manufacturing, metals, energy, mining, construction and logistics look very different. The hand’s job in them often does not. It guides, aligns, holds, carries, separates and retrieves — in similar ways, at similar moments, across every region a global company operates in.
That is what makes a global approach practical. If the functions repeat, the learning can travel: a safer method for guiding a load at one site is a candidate for the same task at twenty others.
A leading indicator for hand exposure
A global company can track hand exposure directly — not instead of injury rates, but alongside them. It takes two counts and one ratio.
Recurring hand-entry tasks
Routine tasks, at each site, where a hand enters a hazard zone: beside a suspended load, between a load and a fixed object, at a closing gap, under a component being set down.
Tasks with a validated method
Of those, the tasks that now have a suitable method keeping the hand farther away — trialled with the crew and checked for reach, visibility, control and release.
Hand-exposure coverage
Count two as a share of count one, by site, by region and for the company as a whole.
Validated tasks ÷ identified tasks
The indicator shows prevention activity before injury numbers change. A rising count one is good news: sites are finding exposure rather than hiding it. A rising ratio shows that exposure is being engineered out, task by task.
Two cautions keep it honest. “Validated” should mean the method has been tried in the real task, not that a tool has been bought. And the indicator should never become a target that rewards sites for reporting fewer hand-entry tasks.
Comparisons need one more safeguard. Sites can define a “task” very differently — one site may record “coil handling” as a single task, another may split it into five. The company needs a consistent task definition, and should review the underlying task records before comparing sites or countries.
From counting where hands were hurt to counting where hands are still exposed — and closing those tasks one by one.
Four places to ask the question before the task exists
The cheapest moment to keep a hand out of a hazard is before the task is designed. A global company already reviews equipment, lifts, maintenance and purchases through central standards. Hand-entry review can sit inside each of them.
Equipment design
New lines, machines and fixtures are reviewed for the moments a hand will be needed to align, feed, clear or retrieve.
Where will a hand have to go to run or clear this?
Lifting arrangements
Lift plans name how the load will be guided, landed and released — not only how it will be rigged.
What controls the load in its last metre?
Maintenance planning
Job plans and permits for recurring work include how components will be held, positioned and moved.
Which step relies on a hand to hold or steady?
Procurement and contractors
Specifications and contractor requirements ask for engineered methods where hands would otherwise control material.
Does this purchase or contract remove a hand-entry step — or add one?
One recurring task at every site
A global programme does not need to begin with a full audit. It can begin with one request to every site manager: identify one recurring task where a hand enters a hazard zone, and assess a safer method for it.
- Pick a task that happens every day or every shift, not a rare one.
- Photograph it before, during and after the hand-control step.
- Name the function the hand performs — guiding, aligning, holding, carrying, retrieving.
- Assess a method that performs the same function from a safer distance: a change to the task, a fixture, a mechanical aid or a hands-free tool.
- Trial it with the crew who do the work, and record what was learned.
Across fifty sites, that is fifty tasks addressed and fifty examples to learn from within a single planning cycle — and a first reading for the leading indicator.
Spread the learning across sites and contractors
Once a site has validated a method, the learning should travel: to sister plants doing the same task, and to the contractors who do much of the lifting, loading and maintenance work on a global company’s sites.
But a method that works at one site is a strong candidate elsewhere, not an automatic answer. Load size, clearance, reach, visibility and the way material is released can differ. Each site should check that the solution suits its own version of the task before standardising it.
Contractors deserve particular attention. They often carry out the highest-exposure handling tasks, and the client’s standard is the most direct way to reach them.
Central standards, local availability
A standard only works if the method is available where the task happens. A multinational can help by naming approved hands-free tools by function in its central standards, listing them in a common catalogue with consistent part numbers, and making them easy for every site to order.
PSC supplies hands-free tools to customers across regions and ships worldwide — through FedEx or the customer’s own freight forwarder — with support to match each tool to the task. For a global customer, PSC supports centralised ordering and consistent commercial terms across its sites. Product pricing is the same for every location; only freight varies with the destination. Each site can order the approved tools the same way, on the same terms. The examples below each take over a function the hand would otherwise perform.
No single tool suits every task. Selection depends on the load, the contact point, the reach and stand-off required, and how the material is released. Guidance and positioning tools replace the hand’s function; they do not replace the crane, the sling or the lifting plan.
Find The Hand™
Start with the task. Not the tool.
Find The Hand™
Where is the hand?
Identify where the hand enters the task or hazard.
Find the Function
Why is it there?
Name what the hand is doing at that moment.
Engineer the Hand Out of the Hazard™
How else can it be done?
Perform the same function with the hand farther from the hazard.
Five steps for the next planning cycle
- Put hand exposure on the global safety agenda as its own topic, not only under PPE.
- Define the two counts and the coverage indicator, and report them alongside injury rates.
- Ask every site to identify one recurring hand-entry task and assess a safer method.
- Add hand-entry review to equipment design, lifting, maintenance and procurement standards.
- Share validated methods across sites and contractors — and check each one locally before it becomes the standard.
Global companies already set the standard for how work is done. They can set it for where the hand goes, too.
Start with one task at every site.
Share photographs of a recurring task for an initial remote review — or arrange a 45-minute Find The Hand™ webinar for your global or regional safety team.
sales@pschandsafety.com · www.pschandsafety.com
Read the methodology: Find The Hand™ by PSC Hand Safety
Site photographs are from PSC field assessments; faces and identifying details have been obscured. Product photographs are PSC reference images.